Skip to product information
1 of 3

The Door Shop

Internal Oak Essential Palermo Pre-Finished 2XG with Clear Etched Glass

Internal Oak Essential Palermo Pre-Finished 2XG with Clear Etched Glass

Regular price £226.44 GBP
Regular price £125.00 GBP Sale price £226.44 GBP
Sale Sold out
VAT Included.

Installation Required?

If you require this door to be installed, please do contact us before placing your order by clicking here!

The finest materials have been used to craft our Palermo Pre-Finished 2XG which include American white oak. The 2/3rd lighting panel will enhance the sense of space and light in your home. This glazed oak door comes with a large pane of clear etched glass at the top of the door, alongside that, the etching matches the grooves on the door, giving it that all important prestige look.

Provided pre-finished, complimented with a clear lacquer, this door is ready to be installed with minimal preparation.

View full details

ADDITIONAL INFORMATION

FEATURES

  • 20mm lippings
  • Luxury deep chamfered U-grooves
  • Engingeered construction for strength and stability
  • XL Joinery 7 panel design
  • Pre-Finished, ready to hang
  • 2/3 glazing

PRODUCT SPECIFICATIONS

  • Family - Palermo
  • Finish - Pre-Finished
  • Materia - lOak
  • Use - Glazed
  • Colour Description - Oak
  • Texture - Natural
  • Construction - Slab
  • Construction Material - Oak veneer
  • Core Material - Particleboard
  • Core Construction Type - Engineered
  • Glazing - Yes
  • Glazing Type - 5mm safety glass
  • Glazing Finish - Clear etched
  • Glazing Safety Specifications - Toughened
  • Glazing Certifications - (2013 version): Part K amalgamates the now defunct Approved Document N,The glass is toughened to either BS6206 / BS 6262 Part 4 or BS EN12150 and BS EN 12600 as stipulated in Approved Document K of the Building Regulations
  • Inlays - Yes
  • Inlay Material - Hardwood
  • Beading Material - None
  • Glue Resin - D3
  • Door Handing - Reversible
  • Lippings - Yes
  • Lipping Details - Lipped on all four sides
  • Lipping Material - Hardwood
  • Lipping Thickness Bottom (mm) - 20
  • Lipping Thickness Sides (mm) - 20
  • Lipping Thickness Top (mm) - 20
  • Veneer - Yes
  • Veneer Material - Solid white oak
  • Veneer Thickness (mm) - 0.6

INSTALLATION

Door Handing - Reversible

Trimmable - Yes

Overall Total Trimming Width (mm) - 30

Overall Trimming Height (mm) - 30

Maximum Trimming From Top (mm) - 15

Maximum Trimming From Bottom (mm) - 15

Maximum Trimming From Each Side (mm) - 15

Recommended Latch Size - 65mm

Door Preparation - Light sanding using 240 or 320 grit sand paper to cut outs and trimmed edges only

Number of Hinges Required - 3

Type of Hinge Required - 3" Butt

Recommended Finish - Osmo door oil, high solid 3060 or 3033. Good quality waterbased clear varnish. To edges and cut outs only

Fitting Instructions

HANDLING AND STORAGE - Doors should always be stored flat, ideally in the same room where they are to be installed. Protect the door from damp and dirt by leaving it in its protective packaging until ready for finishing and fitting. Doors should not be fitted where extremes of temperature or humidity may occur, e.g. in a newly plastered room or near a sauna. In new build situations the doors should only be fitted when the property is ready for final decoration.

INSTALLATION - When trimming a door to fit, 15mm can be removed from each edge of the door to a maximum reduction of 30mm in both the height and width. Any reduction must be removed evenly from each edge of the door, e.g. to trim your door by 8mm in width, remove 4mm off each side. Three hinges should be used to hang all doors, to prevent warping or bowing. Latches and locks should not be fitted adjacent to door mid-rails where the joint may be compromised. All hardware screw holes should be pre-drilled to prevent splitting of the timber.

FINISHING - All fully finished doors will require any bare timber areas caused by trimming and hardware fitting, to be adequately treated before final fitting. Failure to treat all the timber surfaces may lead to excessive changes in moisture content which will cause the timber to shrink or swell, possibly causing splits and distortion. Any unfinished areas will require a light sanding prior to finishing using a fine grade sandpaper (grit number 240 or 320). Please refer to the finish manufacturer’s application instructions for further details.

DO - Use a good quality stain or varnish suitable for veneered doors. Apply to all unfinished, trimmed or cut-out areas. Always apply the manufacturer’s recommended number of coats equally.

DO NOT - Use oils, wax, dyes or preservative treatments Use thinned/mixed paints or stains. Mix incompatible products, e.g. paint on one door face and stain on the opposite face.

MAINTENANCE - To prolong the natural beauty of your door regularly clean the surface with a damp cloth. If the finish appears to fade after a few years simply apply a single coat of finish to renew its lustre.

GUARANTEES & ACCREDITATIONS

  • FSC Certified - No
  • Manufacturers Warranty - Yes
  • Full or Limited Warranty - Limited
  • Warranty Length - 10 Years